CHINA SURPLUS RESOURCE & SELECTION DESK · STATIONARY MINING EQUIPMENT ONLY (HS 8474)
Inspection & Risk Control//8 min read

On-Site Used Mining Equipment Inspection Checklist in China: 12 Mechanical & NDT Checks Before You Wire Deposit

What a real mining engineer inspects inside a Chinese yard or refurbishment workshop—covering ultrasonic crack testing, shaft runout, bronze bushing clearances, bull gear wear, and live no-load running verification.

EXECUTIVE SUMMARY

Before wiring deposit or final balance for used stationary mining machinery in China, an on-site mechanical inspection should verify 12 non-negotiable engineering points: live physical inventory authenticity, cast-frame ultrasonic (UT) crack integrity, eccentric shaft/trunnion concentricity, bronze bushing and spherical bearing clearances, gear tooth wear profile, motor winding insulation (Megger test), hydraulic/lube station pressure stability, wear liner remaining thickness, auxiliary completeness, no-load vibration and bearing temperature rise, electrical frequency compatibility, and export dismantling dimensions.

In This Guide
  1. 1. Why Remote Photos & Generic Certificates Fail on Heavy Used Machinery
  2. 2. Structural & Ultrasonic NDT Verification Comes Before Any Refurbishment Quote
  3. 3. Live No-Load Running Test: Temperature, Vibration & Hydraulic Pressure
  4. 4. Already Negotiating With a Chinese Seller? Book an Independent On-Site Audit

12-Point On-Site Engineering Inspection Matrix for Used Stationary Mining Equipment

Equipment ClassCritical Structural / NDT ChecksDynamic & Electrical ChecksCommon Hidden Defects Caught On-Site
Stationary Jaw CrusherUT crack test on frame welds & pitman; eccentric shaft runout; bearing seat ovalityFlywheel balance, bearing temperature rise during 30-min no-load runRepainted hairline cracks near toggle seat; oversized bearing housings
Hydraulic Cone CrusherMain frame seat flatness; spiral bevel gear tooth pattern; bronze eccentric bushing playHydraulic clearing cylinder pressure hold; lube oil cooler & pump flowCracked socket liner; missing oil-air cooler or stripped bowl threads
Ball / SAG MillShell plate UT thickness; longitudinal weld NDT; hollow trunnion fillet inspection; bull gear backlashPinion mesh noise, reducer oil clarity, main bearing grease/oil conditionFatigue cracks at feed trunnion neck; worn non-reversible ring gear
Flotation & Filter PressTank steel wall thickness; filter beam straightness; hydraulic closing cylinder 20 MPa testImpeller shaft concentricity; motor Megger insulation resistance (MΩ)Corroded tank bottoms masked by tar paint; warped PP filter plates

1. Why Remote Photos & Generic Certificates Fail on Heavy Used Machinery

A freshly sandblasted and repainted cone crusher or ball mill looks identical in WhatsApp photos whether its main frame has an internal stress crack or 15 years of clean life remaining. Likewise, general commercial inspection agencies focus mainly on packing counts and customs HS classification—not eccentric bushing clearances, bull gear tooth profiles, or whether a 50Hz motor will overheat on a 60Hz mine grid.

2. Structural & Ultrasonic NDT Verification Comes Before Any Refurbishment Quote

The single highest-value step during an on-site yard audit is stripping grease and paint from high-stress cast and welded zones for ultrasonic (UT) and magnetic particle (MT) inspection: jaw crusher side frames and pitman hubs, cone crusher main frames, and ball mill trunnion necks and shell welds. A cracked casting turns a bargain machine into scrap steel—catching it on-site before deposit protects 100% of your capital.

3. Live No-Load Running Test: Temperature, Vibration & Hydraulic Pressure

Whenever power is available at the yard or refurbishment workshop, a continuous 30-to-60 minute no-load test reveals hidden bearing wear immediately. Our inspection logs ambient vs. bearing housing temperature via infrared thermometer, checks abnormal gearbox vibration or knocking, verifies hydraulic relief pressure hold on cone crushers and filter presses, and performs Megger insulation checks on high-power motors.

4. Already Negotiating With a Chinese Seller? Book an Independent On-Site Audit

Overseas mine owners and regional agents do not have to buy exclusively from our own stock to benefit from our China engineering desk. If you have already located a used crusher, ball mill, or dismantled plant through another supplier in China, you can hire our team independently to visit the yard, verify genuine ownership and mechanical condition, witness NDT and test runs, and deliver a neutral English inspection report before you commit funds.

Need an Independent Engineer On-Site in China This Week?

Our Sourcing & Inspection Desk conducts standalone machine and workshop audits across China, delivering unedited mechanical measurements, NDT verification, and neutral English reports suitable for both mine owners and regional agents.

Frequently Asked Questions

Can you inspect a used crusher or ball mill that we found through another Chinese supplier?

Yes. We offer standalone on-site machine and workshop audits in China. We verify that the unit physically exists, inspect critical structural and wear tolerances, record live test videos, and deliver a neutral English engineering report before you wire payment.

Does your technical inspection replace destination SGS or Bureau Veritas PVoC certificates?

No—they complement each other. Our engineering audit protects your mechanical and metallurgical investment (cracks, gears, bearings, electrical specs), and once approved we coordinate smoothly with SGS, BV, or Intertek to issue mandatory destination customs certificates (PVoC / CoC / CBCA).

CONTINUE READING